How to make a $1,000,000 Christmas Tree
The following article first appeared in the Calgary Herald on December 25, 2018.
I’m a christian, and the idea of making a tree that would make the world a better place was a pretty good one.
So, when my husband and I were planning our big tree, we asked ourselves a few questions about how to make it.
We had a couple of ideas, and then we had to figure out how to do them.
We came up with the following list of things we would need to do: A tree.
A tree is a big, heavy, heavy tree.
I was going to say something big and tall, but it didn’t matter.
A tree is the biggest thing you can ever build.
A tall tree is like a tower.
How do you make a tree with two feet of lumber?
First, you cut a tree in half.
You have to do this on the outside of the tree, but on the inside, you have to cut a piece of plywood into two pieces, each about as big as the trunk of a house.
Cut two of those pieces into one.
Next, you use two pieces of ply to make the trunk.
Cut one piece of the ply into a 90-degree angle.
You then need to cut two of the smaller pieces out of the two that were cut into one piece.
Now, when you’re cutting the branches, make sure you don’t get them all the way to the top.
This will help prevent them from growing too tall.
If you cut them too short, they will grow too high.
Now you need to trim the excess wood away.
Now that you’ve made a tree, you need some leaves.
You need about 1/4 inch of each.
If it’s too short or too long, you will have a problem.
Cut them to about 1 1/2 inches.
They should look like this: A few things to keep in mind.
First, when trimming a tree you want to leave the branch ends in the middle.
This way, you don,t end up with a huge piece of wood that is too big.
If you cut it too short and the branches are too high, the leaves will end up sticking out.
Second, you want the ends of the branches to be at least 1 1 1-2 inches apart.
Third, you may want to trim some of the wood away from the top of the trunk, but don’t cut all the wood off the top just yet.
Fourth, don’t be afraid to cut off the ends with a hacksaw or a mallet.
You may want a bit of wood around the edges of the stump, but you don`t want to completely remove the bark.
You also want to cut the ends off to the outside so that the leaves are still attached.
Fifth, don`s want to keep the end of the branch too short.
You want the tree to be tall enough to stand on its own.
What we didn’t know is that the trees that I had in my backyard were all much taller than the trees I grew here.
And if we were lucky, the tree that we grew in my yard would grow even taller than my tree!
We had a great experience with our tree.
It didn’t take long for us to realize how big it was.
In fact, it was so big, it took a bit longer than we expected to get it to hang.
We decided to trim a few branches off of the top to create the base.
I cut the top down to about an inch thick, and it took us about an hour to do the job.
After the cut, I then used a small saw to cut down the branches into a line about one-half inch wide and about two inches deep.
Once we had our branches, we made a couple cuts down the center of the sides of the base, then we went to work on the ends.
I cut the edges to about three-quarters of an inch in width.
Then, I cut a long piece of lumber about one inch wide.
I then trimmed that down to one-quarter inch.
With the pieces that we cut, we started cutting the ends, which was the hard part.
For the ends I cut to the ends closest to the trunk where it meets the branches.
When I was cutting the leaves, I was careful to trim them to the edges and not overhang the tree.
If I did that, the branches would get in the way of the leaves.
At this point, I just took a piece off of each branch.
To finish the base of the big tree we were going to build, I used a drill to cut some pieces of lumber to about two-thirds of an inches in length.
As I was about to cut, the base came down.
I noticed that I was making a